Command Status
ICL version 2.0.0.226ac9f0_126_20240417
Generic Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| icl_info | ✅ | ✅ | ✅ | |
| icl_shutdown | ✅ | ✅ | ✅ | |
| icl_binMode | ✅ | ❓ | ✖️ | how will this command affect the work of the devices |
Monochromator Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| mono_discover | ✅ | ✅ | ✅ | |
| mono_list | ✅ | ✅ | ✅ | |
| mono_listCount | ✅ | ✅ | ✅ | |
| mono_open | ✅ | ✅ | ✅ | |
| mono_close | ✅ | ✅ | ✅ | |
| mono_isOpen | ✅ | ✅ | ✅ | |
| mono_isBusy | ✅ | ✅ | ✅ | |
| mono_init | ✅ | ✅ | ⚠️ | there is no way to reliably understand if a homing cycle was done after the last power-up |
| mono_getConfig | ✅ | ✅ | ✅ | |
| mono_getPosition | ✅ | ✅ | ✅ | |
| mono_setPosition | ✅ | ✖️ | ⚠️ | this operation will un-calibrate the device |
| mono_moveToPosition | ✅ | ✅ | ✅ | |
| mono_getGratingPosition | ✅ | ✅ | ✅ | |
| mono_moveGrating | ✅ | ✅ | ✅ | we have to wait 2 mins per test |
| mono_getFilterWheelPosition | ✅ | ✅ | ⛔ | [E];-510;Error Mono Command Not Supported |
| mono_moveFilterWheel | ✅ | ✅ | ⛔ | [E];-510;Error Mono Command Not Supported |
| mono_getMirrorPosition | ✅ | ✅ | ✅ | |
| mono_moveMirror | ✅ | ✅ | ✅ | |
| mono_getSlitPositionInMM | ✅ | ✅ | ✅ | |
| mono_moveSlitMM | ✅ | ✅ | ⚠️ | Slit C is not moving |
| mono_shutterSelect | ✅ | ✅ | ⚠️ | [E];-519;Mono must be configured for internal shutter mode |
| mono_shutterOpen | ✅ | ✅ | ⚠️ | [E];-519;Mono must be configured for internal shutter mode |
| mono_shutterClose | ✅ | ✅ | ⚠️ | [E];-519;Mono must be configured for internal shutter mode |
| mono_getShutterStatus | ✅ | ✅ | ⚠️ | [E];-519;Mono must be configured for internal shutter mode |
| mono_getSlitStepPosition | ✅ | ✅ | ✅ | |
| mono_moveSlit | ✅ | ✅ | ✅ | Slit C is not moving |
CCD Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| ccd_discover | ✅ | ✅ | ✅ | |
| ccd_list | ✅ | ✅ | ✅ | |
| ccd_listCount | ✅ | ✅ | ✅ | |
| ccd_open | ✅ | ✅ | ✅ | |
| ccd_close | ✅ | ✅ | ✅ | |
| ccd_isOpen | ✅ | ✅ | ✅ | |
| ccd_restart | ✅ | ✖️ | ✅ | device restarting confirmed manuall by observing USB connection |
| ccd_getConfig | ✅ | ✅ | ✅ | |
| ccd_getChipSize | ✅ | ✅ | ✅ | |
| ccd_getChipTemperature | ✅ | ✅ | ✅ | |
| ccd_getGain | ✅ | ✅ | ✅ | |
| ccd_setGain | ✅ | ✅ | ✅ | |
| ccd_getSpeed | ✅ | ✅ | ✅ | |
| ccd_setSpeed | ✅ | ✅ | ✅ | |
| ccd_getFitParams | ✅ | ✅ | ✅ | |
| ccd_setFitParams | ✅ | ✅ | ⛔ | how should these parameters be used/set |
| ccd_getExposureTime | ✅ | ✅ | ✅ | |
| ccd_setExposureTime | ✅ | ✅ | ✅ | |
| ccd_getTimerResolution | ✅ | ✅ | ✅ | |
| ccd_setTimerResolution | ✅ | ✅ | ✅ | |
| ccd_setAcqFormat | ✅ | ✖️ | ❓ | how can this be tested with code only? |
| ccd_setRoi | ✅ | ✅ | ✅ | |
| ccd_getXAxisConversionType | ✅ | ✅ | ✅ | |
| ccd_setXAxisConversionType | ✅ | ✅ | ✅ | |
| ccd_getDataRetrievalMethod | ⛔ | ✖️ | ✖️ | "[E];-2;ccd_getDataRetrievalMethod;Command handler not found" |
| ccd_setDataRetrievalMethod | ⛔ | ✖️ | ✖️ | "[E];-2;ccd_getDataRetrievalMethod;Command handler not found" |
| ccd_getAcqCount | ✅ | ✅ | ✅ | |
| ccd_setAcqCount | ✅ | ✅ | ✅ | |
| ccd_getCleanCount | ✅ | ✅ | ✅ | |
| ccd_setCleanCount | ✅ | ✅ | ✅ | |
| ccd_getDataSize | ✅ | ✅ | ✅ | |
| ccd_getTriggerIn | ✅ | ✅ | ✅ | |
| ccd_setTriggerIn | ✅ | ✅ | ✅ | |
| ccd_getSignalOut | ✅ | ✅ | ✅ | |
| ccd_setSignalOut | ✅ | ✅ | ✅ | |
| ccd_getAcquisitionReady | ✅ | ✅ | ✅ | |
| ccd_setAcquisitionStart | ✅ | ✅ | ✅ | |
| ccd_getAcquisitionBusy | ✅ | ✅ | ✅ | |
| ccd_setAcquisitionAbort | ✅ | ✖️ | ❓ | what is the expected 'Abort' procedure? |
| ccd_getAcquisitionData | ✅ | ✅ | ✅ |
Single Chanel Detector Commands
| Command | Implemented | Tested | Status | Comment |
|---|---|---|---|---|
| scd_discover | ✖️ | ✖️ | ✖️ | |
| scd_list | ✖️ | ✖️ | ✖️ | |
| scd_listCount | ✖️ | ✖️ | ✖️ | |
| scd_open | ✖️ | ✖️ | ✖️ | |
| scd_close | ✖️ | ✖️ | ✖️ | |
| scd_isOpen | ✖️ | ✖️ | ✖️ |
ICL version 2.0.0.125.45db7b8c
Generic Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| icl_info | ✅ | ✅ | ✅ | |
| icl_shutdown | ✅ | ✅ | ✅ | |
| icl_binMode | ✅ | ❓ | ✖️ | how will this command affect the work of the devices |
Monochromator Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| mono_discover | ✅ | ✅ | ✅ | |
| mono_list | ✅ | ✅ | ✅ | |
| mono_listCount | ✅ | ✅ | ✅ | |
| mono_open | ✅ | ✅ | ✅ | |
| mono_close | ✅ | ✅ | ✅ | |
| mono_isOpen | ✅ | ✅ | ✅ | |
| mono_isBusy | ✅ | ✅ | ✅ | |
| mono_init | ✅ | ✅ | ⚠️ | there is no way to reliably understand if a homing cycle was done after the last power-up |
| mono_getConfig | ✅ | ✅ | ✅ | |
| mono_getPosition | ✅ | ✅ | ✅ | |
| mono_setPosition | ✅ | ✖️ | ⚠️ | this operation will un-calibrate the device |
| mono_moveToPosition | ✅ | ✅ | ✅ | |
| mono_getGratingPosition | ✅ | ✅ | ✅ | |
| mono_moveGrating | ✅ | ✅ | ✅ | we have to wait 2 mins per test |
| mono_getFilterWheelPosition | ✅ | ✅ | ⛔ | [E];-510;Error Mono Command Not Supported |
| mono_moveFilterWheel | ✅ | ✅ | ⛔ | [E];-510;Error Mono Command Not Supported |
| mono_getMirrorPosition | ✅ | ✅ | ✅ | |
| mono_moveMirror | ✅ | ✅ | ✅ | |
| mono_getSlitPositionInMM | ✅ | ✅ | ✅ | |
| mono_moveSlitMM | ✅ | ✅ | ⚠️ | Slit C is not moving |
| mono_shutterSelect | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_shutterOpen | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_shutterClose | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_getShutterStatus | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_getSlitStepPosition | ✅ | ✅ | ✅ | |
| mono_moveSlit | ✅ | ✅ | ⚠️ | Slit C is not moving |
CCD Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| ccd_discover | ✅ | ✅ | ✅ | |
| ccd_list | ✅ | ✅ | ✅ | |
| ccd_listCount | ✅ | ✅ | ✅ | |
| ccd_open | ✅ | ✅ | ✅ | |
| ccd_close | ✅ | ✅ | ✅ | |
| ccd_isOpen | ✅ | ✅ | ✅ | |
| ccd_restart | ✅ | ✖️ | ✅ | |
| ccd_getConfig | ✅ | ✅ | ✅ | |
| ccd_getChipSize | ✅ | ✅ | ✅ | |
| ccd_getChipTemperature | ✅ | ✅ | ✅ | |
| ccd_getGain | ✅ | ✅ | ✅ | |
| ccd_setGain | ✅ | ✅ | ✅ | |
| ccd_getSpeed | ✅ | ✅ | ✅ | |
| ccd_setSpeed | ✅ | ✅ | ✅ | |
| ccd_getFitParams | ✅ | ✅ | ✅ | |
| ccd_setFitParams | ✅ | ✅ | ⛔ | how should these parameters be used/set |
| ccd_getExposureTime | ✅ | ✅ | ✅ | |
| ccd_setExposureTime | ✅ | ✅ | ✅ | |
| ccd_getTimerResolution | ✅ | ✅ | ✅ | |
| ccd_setTimerResolution | ✅ | ✅ | ⛔ | [E];-316;CCD does not support Timer Resolution Token = 500 |
| ccd_setAcqFormat | ✅ | ✖️ | ❓ | how can this be tested with code only? |
| ccd_setRoi | ✅ | ✅ | ✅ | |
| ccd_getXAxisConversionType | ✅ | ✅ | ✅ | |
| ccd_setXAxisConversionType | ✅ | ✅ | ✅ | |
| ccd_getDataRetrievalMethod | ✖️ | ✖️ | ✖️ | |
| ccd_setDataRetrievalMethod | ✖️ | ✖️ | ✖️ | |
| ccd_getAcqCount | ✅ | ✅ | ✅ | |
| ccd_setAcqCount | ✅ | ✅ | ✅ | |
| ccd_getCleanCount | ✅ | ✅ | ✅ | |
| ccd_setCleanCount | ✅ | ✅ | ✅ | |
| ccd_getDataSize | ✅ | ✅ | ✅ | |
| ccd_getTriggerIn | ✖️ | ✖️ | ✖️ | |
| ccd_setTriggerIn | ✖️ | ✖️ | ✖️ | |
| ccd_getSignalOut | ✖️ | ✖️ | ✖️ | |
| ccd_setSignalOut | ✖️ | ✖️ | ✖️ | |
| ccd_getAcquisitionReady | ✅ | ✅ | ✅ | |
| ccd_setAcquisitionStart | ✅ | ✅ | ✅ | |
| ccd_getAcquisitionBusy | ✅ | ✅ | ✅ | |
| ccd_setAcquisitionAbort | ✅ | ✖️ | ❓ | what is the expected 'Abort' procedure? |
| ccd_getAcquisitionData | ✅ | ✅ | ✅ |
Single Chanel Detector Commands
| Command | Implemented | Tested | Status | Comment |
|---|---|---|---|---|
| scd_discover | ✖️ | ✖️ | ✖️ | |
| scd_list | ✖️ | ✖️ | ✖️ | |
| scd_listCount | ✖️ | ✖️ | ✖️ | |
| scd_open | ✖️ | ✖️ | ✖️ | |
| scd_close | ✖️ | ✖️ | ✖️ | |
| scd_isOpen | ✖️ | ✖️ | ✖️ |
ICL version 2.0.0.124.b4cc4e55
Generic Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| icl_info | ✅ | ✅ | ✅ | |
| icl_shutdown | ✅ | ✅ | ✅ | |
| icl_binMode | ✅ | ❓ | ✖️ | how will this command affect the work of the devices |
Monochromator Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| mono_discover | ✅ | ✅ | ✅ | |
| mono_list | ✅ | ✅ | ✅ | |
| mono_listCount | ❓ | ✖️ | ✖️ | how is this different from mono_discover |
| mono_open | ✅ | ✅ | ✅ | |
| mono_close | ✅ | ✅ | ✅ | |
| mono_isOpen | ✅ | ✅ | ✅ | |
| mono_isBusy | ✅ | ✅ | ✅ | |
| mono_init | ✅ | ✅ | ⚠️ | there is no way to reliably understand if a homing cycle was done after the last power-up |
| mono_getConfig | ✅ | ✅ | ✅ | |
| mono_getPosition | ✅ | ✅ | ✅ | |
| mono_setPosition | ✅ | ✖️ | ⚠️ | this operation will un-calibrate the device |
| mono_moveToPosition | ✅ | ✅ | ✅ | |
| mono_getGratingPosition | ✅ | ✅ | ✅ | |
| mono_moveGrating | ✅ | ✅ | ✅ | we have to wait 2 mins per test |
| mono_getFilterWheelPosition | ✅ | ✅ | ⛔ | [E];-510;Error Mono Command Not Supported |
| mono_moveFilterWheel | ✅ | ✅ | ⛔ | [E];-510;Error Mono Command Not Supported |
| mono_getMirrorPosition | ✅ | ✅ | ✅ | |
| mono_moveMirror | ✅ | ✅ | ✅ | |
| mono_getSlitPositionInMM | ✅ | ✅ | ✅ | |
| mono_moveSlitMM | ✅ | ✅ | ✅ | Slit C is not moving |
| mono_shutterSelect | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_shutterOpen | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_shutterClose | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_getShutterStatus | ✅ | ✅ | ⛔ | [E];-519;Mono must be configured for internal shutter mode |
| mono_getSlitStepPosition | ✅ | ✅ | ✅ | |
| mono_moveSlit | ✅ | ✅ | ✅ | Slit C is not moving |
CCD Commands
| Command | Implemented | Tests available | Status | Comment |
|---|---|---|---|---|
| ccd_discover | ✅ | ✅ | ✅ | |
| ccd_list | ✅ | ✅ | ✅ | |
| ccd_listCount | ❓ | ✖️ | ✖️ | how is this different fromccd_discover |
| ccd_open | ✅ | ✅ | ✅ | |
| ccd_close | ✅ | ✅ | ✅ | |
| ccd_isOpen | ✅ | ✅ | ✅ | |
| ccd_restart | ✅ | ✖️ | ❓ | how can this be tested with code only? |
| ccd_getConfig | ✅ | ✅ | ✅ | |
| ccd_getChipSize | ✅ | ✅ | ✅ | |
| ccd_getChipTemperature | ✅ | ✅ | ✅ | |
| ccd_getNumberOfAvgs | ✅ | ✅ | ⛔ | [E];-315;CCD does not support averaging |
| ccd_setNumberOfAvgs | ✅ | ✅ | ⛔ | [E];-315;CCD does not support averaging |
| ccd_getGain | ✅ | ✅ | ✅ | |
| ccd_setGain | ✅ | ✅ | ✅ | |
| ccd_getSpeed | ✅ | ✅ | ✅ | |
| ccd_setSpeed | ✅ | ✅ | ✅ | |
| ccd_getFitParams | ✅ | ✅ | ✅ | |
| ccd_setFitParams | ✅ | ✅ | ⛔ | how should these parameters be used/set |
| ccd_getExposureTime | ✅ | ✅ | ✅ | |
| ccd_setExposureTime | ✅ | ✅ | ✅ | |
| ccd_getTimerResolution | ✅ | ✅ | ✅ | |
| ccd_setTimerResolution | ✅ | ✅ | ⛔ | [E];-316;CCD does not support Timer Resolution Token = 500 |
| ccd_setAcqFormat | ✅ | ✖️ | ❓ | how can this be tested with code only? |
| ccd_setRoi | ✅ | ✖️ | ❓ | how can this be tested with code only? |
| ccd_getXAxisConversionType | ✅ | ✅ | ✅ | |
| ccd_setXAxisConversionType | ✅ | ✅ | ✅ | |
| ccd_getDataRetrievalMethod | ✖️ | ✖️ | ✖️ | |
| ccd_setDataRetrievalMethod | ✖️ | ✖️ | ✖️ | |
| ccd_getAcqCount | ✅ | ✅ | ✅ | |
| ccd_setAcqCount | ✅ | ✅ | ✅ | |
| ccd_getCleanCount | ✅ | ✅ | ✅ | |
| ccd_setCleanCount | ✅ | ✅ | ✅ | |
| ccd_getDataSize | ✅ | ✅ | ✅ | |
| ccd_getTriggerIn | ✖️ | ✖️ | ✖️ | |
| ccd_setTriggerIn | ✖️ | ✖️ | ✖️ | |
| ccd_getSignalOut | ✖️ | ✖️ | ✖️ | |
| ccd_setSignalOut | ✖️ | ✖️ | ✖️ | |
| ccd_getAcquisitionReady | ✅ | ✅ | ✅ | |
| ccd_setAcquisitionStart | ✅ | ✅ | ✅ | |
| ccd_getAcquisitionBusy | ✅ | ✅ | ✅ | |
| ccd_setAcquisitionAbort | ✅ | ✖️ | ❓ | what is the expected 'Abort' procedure? |
| ccd_getAcquisitionData | ✅ | ✅ | ⛔ | [E];-326;Error Data Formatting Error |
Single Chanel Detector Commands
| Command | Implemented | Tested | Status | Comment |
|---|---|---|---|---|
| scd_discover | ✖️ | ✖️ | ✖️ | |
| scd_list | ✖️ | ✖️ | ✖️ | |
| scd_listCount | ✖️ | ✖️ | ✖️ | |
| scd_open | ✖️ | ✖️ | ✖️ | |
| scd_close | ✖️ | ✖️ | ✖️ | |
| scd_isOpen | ✖️ | ✖️ | ✖️ |